China best sale Polyimide UV AB Film with High Temperature Resistance A3 UV Film

1. Roll-to-roll printer products represent the wave of inkjet printing in the 21st century.

2. New ink spray printing method – the computer directly outputs inkjet to create higher printing.

3. The roll-to-roll printer is a “non-contact with the object” inkjet printing type — digital printing equipment

Our UV diy 6040 size cylinder phone case universal digital flatbed New Launched acrylic uv silicone ODM a3 digital flatbed uv High quality wood glass metal acrylic plastic leather phone shell case uv led Ceramic uv flat bed printer a2 6040 focus alpha jet uv printing machinesticker printing machine for golf was warm welcomed by our clients.

The faults of the UV flatbed printer reset are mainly concentrated in four aspects: the printing can be reset without response, the reset Z axis only rises or falls, the normal reset cannot be completed, and X always moves to the right during reset. The solution to each fault is different.

With the TODOjet powder machine,you can set up different temperatures,the front heating, top heating and back heating. This will prevent the film from oil or moisture.

UV Curable Varnish UV Primer Liquid For UV Flatbed Printer machine varnish coating for phone case acrylic glass wood

Symptoms of poor ink output from uv flatbed printers are: flying ink, dripping ink, drawing and so on. There are roughly eight kinds of reasons that cause this kind of failure. In actual application, the UV flatbed printer design varies from different manufacturers. Some may have 10 reasons, and some may have 6 reasons. But mastering the following 7 kinds can solve the problem that 99% of the nozzles have poor ink discharge.

A3 size DTF powder shaking machine
new solution for universal print
free teaching and life-long after sale service

Adjust the thermostat and timer of the heat press machine to the desired temperature and time.
1.Lay the substrate flat on the silicone plate, then place the offset heat transfer drawing on the substrate, and press the handle down firmly until it is completely closed.
2.When the time indicated for hot stamping is up, the buzzer will sound, and the handle will be lifted back to its original position.
3.If it is cold torn, the heat transfer paper should be torn off after cooling; if it is hot torn, the heat transfer paper should be torn off immediately after the hot stamping is completed.

Printer not printing colors correctly is a common problem printer owners experience from time to time. Printers can be pretty confusing machines. what if the printer that you just bought suddenly decided to stop printing colors right. How are you going to print now? Today, we’re going to help you fix your printer not printing in real color and tell you how you can prevent this printer issue from reoccurring.

TODOjet offers premium quality DTF ink for Epson printers and printheads. These are specially formulated direct to film printing inks designed to work with a wide variety of DTF printers.

The advantage of white ink heat transfer is that it can transfer high-precision pictures and other colorful pattern designs. The actual effect is quite close to the computer hand-painted manuscript. The lack of part: if you touch it hard, you will feel a strong sense of collagen fibers, and the ventilation effect is not good. If you only do simple pattern decoration design for clothing products, bags, and pillows, then you don’t need to consider the ventilation problem.

المكون الأساسي لآلة الضغط الحراري هو لوحة التسخين ، لذا يجب الانتباه عند اختيار آلة الضغط الحراري.

A3 DTF Pro textile printer is widely used for different products, for example T-shirt, hats, shoes, bags. It requires a DTF printer, a shake powder machine and a heat press to get final products. Since it is cost effective, small size and environmentally friendly, customers who want to start new business are very interested in it.

Using the shake powder could consider these procedures.
Dusting.
1.What is the powder sprinkled with?Hot melt powder, when the heat is sticky, after the formation of glue coating;
2.Why?Stick hot melt stick to the dry ink to help eventually form the coating;
3.How to sprinkle, sprinkle how fast?Can adjust the knob on the shake powder machine;
4.How much?The powder is about 2-3cm thick to stop sprinkling the powder.
Shaking.
1.Why shake powder?Shake off the excess powder on the ink and film adhesion, so that the powder is thin and evenly attached to the ink.
2.Shake powder speed.Depending on the situation, the knob on the condition machine, about 2-3 gear ok.
Drying.

1.Why drying?Melt the hot melt powder to create a reprint pattern coating;.
2.How long will it bake?Undefinite, depending on the specific situation, mainly to ensure that the pattern feels no powder, hot melt powder all melted into coating.
3.Temperature? 90-130 ° C is ok.

Powder shaking machine usually together with our 60cm DTF printer, it can keep continous automatic dusting powder and curing the PET film during printing.The speed can match with 2 heads 4720/i3200 DTF printer. After curing, you can store the printed PET film for heat transfer use.These released PET films are suitable for any fabric garment printing, like T-shirt printing,chemical fiber, non-woven fabric printing,linen printing,canvas printing,leather printing,silk printing,etc.

1. keep the machine clean:keep the important parts of the machine clean, can not be stained with oil and dust, keep the hot transfer film clean, can not be stained with fingerprints and dust, keep the bearing products clean, no dust, oil, keep the hands clean, no oil, no sweat.
2.hot stamping pressure:hot stamping pressure must be adjusted to the most appropriate, otherwise too big and easy to hurt the glue head and be hot material, too small and affect the hot stamping effect.The pressure shall be locked after adjusting to the best stamping pressure to avoid change in mass production.
3. hot temperatureIt is easy to damage the bearing material, too low hot temperature may not be able to reach the normal transfer printing.Hot temperature should be determined by the bearing material, flower film, heat transfer machine, these factors, different materials have different hot temperature.
4.hot stamping speed:hot stamping time (speed) should be determined according to the specific hot stamping, in the case of ensuring the hot stamping effect, the faster the speed, the higher the production efficiency, but some products due to some special conditions must use slow speed

During the curing process, the hot melt powder may produce some gas, here we need the air purifier for cleaning. TODOjet can offer you one-stop solutions of DTF printing, such as the DTF printer, powder shaker machine,PET film, hot melt powder,pigment ink and so on.

Full series large format powder shaking machine, from 60cm to 120cm size, can match with your large format DTF printer well. This powder curing machine also with take-up system. Fast speed can match both 2 heads or 4 heads printer.

PET detached film is a material commonly used in thermal transfer printing, the substrate is PET, after being coated with silicone oil, so it is also called silicone oil film.There are hot peel and cool peel . After anti-static and anti-scratch treatment, the product has a very good adsorption and fit.

Pure black when printing is generally used for smaller characters. If the full-color black (C100 M100 Y100 K100) is used, the ink concentration is too high, the ink is not easy to dry and easy to print. Therefore, it is recommended to use monochrome black (C0 M0 Y0 K100).

Printing and dyeing of all fiber fabrics, including pure cotton, rayon, linen, modal, wool, silk and other protein fibers; polyester, nylon, acrylic and other chemical fibers and other blended products.
Specifically used in pure cotton fabrics, garments, T-shirts, cut pieces, decorative fabrics, wall coverings, curtains, fabric sofas, bedding.

This neutral ink was created to enable printing on items such as coolers and plastic bottles without cracking or distorting the image. This type is available for all of TODOJet ’ UV printers, including Cyan, Magenta, Yellow, Black, White, and Varnish.
Full CMYKWW+V color range
High durability

Environmentally friendly, no waste, small footprint, unlimited fabrics, soft and washable, suitable for personalized heat transfer customization and batch automated production of various fabrics.

How to repair uv flatbed printer to save more money? Answer: No. This is obviously a joke. In fact, unless there is a major problem, there is no need to repair it in consideration of economic benefits ,then giving up. Of course, don’t expect that the equipment will not malfunction. This non-existent, once has a problem. What can be done is to solve it as soon as possible to avoid greater losses.

Type:Water Based Ink
Printing Type:Digital printing
Place of Origin:Henan
Brand Name:TODOjet
Model Number:CMYKLcLmW
Key name:Textile Pigment ink 6 Color DTF Printer Ink For Inkjet Printer

Each digital inkjet printer comes in a similar way: a print head.All component print heads for small or large formate inkjet printers, printing ink on all different types of media.The inkjet print heads spray the ink onto paper or other media in a controlled way to provide the desired image. Our TODOjet printesr usually use the Epson F1080 and Epson i3200 printhead.

Factory delivery: provide technical guidance ink/powder/heat transfer film offset heat transfer printer one-stop supply,Use the special paint ink for transfer film to print the pattern on the PET film, directly remove dust, no need to cut, no need to discharge waste, and the fast transfer of natural hollowing is suitable for any fabric.

Advantages
1.With timing function, automatic sound &light alarm after completion
2.With lock catch and sealing strip
3.Excellent heat preservation
4.Rapid temperature rise
5.Up to 6 heating tubes
6.Ensure that every corner of the full width can melt
7.It makes the image quality and firmness transferred to the fabric better

1.White ink with color ink: soft to the touch
2.No waste, just tear it off
3.Hollow pattern, no need to engrave, fine lines, small characters and fine dots can be printed naturally

1, Wear masks, do not need to be particularly expensive, generally a unit price of about 3RMB;
2. Wear disposable gloves to avoid direct contact between UV ink and the skin on your hands, some people will be allergic;