38 x 38 cm 15″ x 15″ Printing Flat Digital Transfer Sublimation Heat Press Machine For T-Shirt Clothing

TYPE: UV INK
SUITABLE FOR: Printer with Epson DX7 DX5 XP600 TX800 head
COLOR: CMYK+LC+LM+White+Varnish
TESTING: 100% testing on the machine before shipment
HARD UV INK:
mainly printing on hard type materials, like Wood, Glass, Acrylic, Metal, Crystal, etc.
SOFT UV INK:
mainly printing on soft type materials, like leather, vinyl, TPU, EVA, wall paper, lamp box, etc.

Hotsale A3 DTF printer:
* 2 XP600 printheads support fluoresent ink printing
* Fast speed, can each to 5 sqm/h (6 hours can finish one 100m roll film)
* Support vent holes solution,keep the garment breathable function after transfered
* No limit of fabrics

UV flatbed printer safety equipment mainly includes three aspects: Electrical connection, ground wire, and mobile machine. Each part must be installed and banned accordingly. It must be strictly observed to prevent safety accidents.

Powder machine usually come with DTF printer, for printed film powder coating and curing.Then the film can be transferred on any kind of fabric materials.

UV Curable Varnish UV Primer Liquid For UV Flatbed Printer machine varnish coating for phone case acrylic glass wood

1. Simple control buttons
The key functions are clear and easy to operate, just one touch
2. Four-color printing
The colors are more vivid and rich, and the hot stamping effect is good

K-PRINT is one of the largest and most influential international exhibitions in Korea, with an exhibition scale of 25,000 square meters and more than 400 exhibitors. It is an exhibition with great development prospects selected by the Ministry of Industry, Trade and Resources of Korea. , is also a printing feast created by the official comprehensively integrating multiple resources.

UV flatbed printers have pass trace, which is theoretically unavoidable, and mechanical errors cannot be eliminated to zero. But the higher the accuracy, the smaller the pass trace phenomenon and will not affect the printing quality. The cause of the pass trace of the pattern: the print feathering is too low, the two-way printing is too fast, the Y-axis belt is loose, the nozzle is in a bad state, and the ink is broken.

When it is found that the pattern printed by the UV flatbed printer has left and right, and the upper and lower deviations are not aligned, it means that the x and y direction is misaligned, and the printing needs to be suspended immediately. Because the structural design and components of the x and y axis are different, the causes of fault and corresponding solutions are also different.

1.Universal matching, easy to use, small size, time-saving and labor-saving
2. Suitable for digital printing and other industries
3. Digital offset heat transfer, one-piece molding
4. No engraving, no waste discharge, no white edge, environmental protection
5. Timing control switch, timing at will
6. Full body sheet metal design, durable and durable
7. Comes with a baking tray limit device, which is more convenient
8. Equipped with power fuse device, more assured to use

No need to engrave waste and lamination, improve production efficiency, unlimited patterns, natural hollowing, lighter and breathable, short cycle and fast delivery, breaking through the limitations of traditional process color registration plate making, no plate making, 1 piece minimum order cost-effective, no high cost The investment in equipment and venues greatly reduces the investment cost.

1. More choices on dark colored fabric
2. Reducing your production cost
3. Better print out on performance
4. Environmental friendly

The produced glue has the characteristics of water resistance, good fastness, fast drying speed, not easy to block the network, and does not affect the color of the ink, and is a new type of environmentally friendly material.

A3 new digital offset printer, we develop and produce independently, do not use Epson L1800 and 1390 modification, our machine structure is reasonable and completely similar to industrial machine structure, using PP color management software color does not cast color.

The difference between white ink heat transfer and heat sublimation
The temperature and time of hot stamping are different:
Generally speaking, the hot stamping temperature of white ink heat transfer is about 160 degrees, and the time is about 13 seconds (the hot melt adhesive used by different manufacturers is different, the temperature and time of hot stamping may be different, but most of the values are in this range) , and the sublimation paper temperature is between 200-230 degrees, and the time is about 15-20 seconds.

A3 DTF Printer, Our Latest A3DTF Printer is Officially Released. Direct to Film printing, or DTF, is a new technology that allows users to print designs onto special films. And then do heat transfer in any fabric，A very good way to do for every craft and DIY.

To understand the market prospects of UV printers, we can start from the three aspects of UV printer equipment itself, the materials that can be printed, and the applied industry.

RGB color model refers to the three primary colors of light: Red, Green, and Blue,the three primary color light with different proportions of the sum, can produce a variety of color light, in theory, red, green, blue light can be mixed out of all colors.

Garment printers can print on various rolls or sheets of materials, such as: thermal transfer film, film, self-adhesive, PU film, etc. At present, the most popular application is in the clothing industry.

1.White ink with color ink: soft to the touch
2.No waste, just tear it off
3.Hollow pattern, no need to engrave, fine lines, small characters and fine dots can be printed naturally

As professional DTF printer supplier, we can also offer you related powder shaking machine, full series powder heating and curing machine like 30cm width, 60cm width and also 120cm width can meet your different demand.

UV DTF AB Film for digital uv dtf printer is hot, there are different types in the market. Some film A needs to print on transparent film, then laminating film B with heating; some film A needs to white paper film, then laminating film B with heating. Our this new upgraded AB film is printing on whtie paper side, then laminating film B with only pressure, no need heating.

-Environmentally friendly and non-toxic
-Support customization, free design
-High-definition printing, quality assurance
-Azo free, oeko-tex standard
-Choose TODOjet product quality and after-sales guarantee

When the UV flatbed printer nozzle is used for a long time, it is easy to ink on the surface area. If left alone, after a long time, the nozzle will easily become clogged. There are generally five causes of this phenomenon. Depending on the design of the UV flatbed printer from different manufacturers, there may be 7 or 4 phenomenon, but mastering these five can basically solve more than 90% of the ink accumulation problem.

TODOjet is a professional manufacture of DTF printer,we can also offer you heat transfer pet film powder dusting, shaking and heating machine. Printed film can be heat transferred on any kind of fabrics.

The advantage of white ink heat transfer is that it can transfer high-precision pictures and other colorful pattern designs. The actual effect is quite close to the computer hand-painted manuscript. The lack of part: if you touch it hard, you will feel a strong sense of collagen fibers, and the ventilation effect is not good. If you only do simple pattern decoration design for clothing products, bags, and pillows, then you don’t need to consider the ventilation problem.

When the temperature gets colder every year, the number of failures of UV printers will also increase. It is mainly concentrated in four aspects: blockage and disconnection of nozzles, solidification and condensing of consumables, electrostatic interference, and unstable voltage. How to prevent these situations in advance?

The poor adhesion of the material pattern of the UV flatbed printer is a headache. The printed pattern is peeled off with a slight scratch. Even if the printing effect is even better, it has no shelf life and practicality. There are six reasons for this: temperature and humidity relations, ink deterioration, material problems, UV lamp problems, too fast speed,the ink is not dry, and residual cleaning liquid.

UV flatbed printer print head heating does not heat up, it will directly affect the normal ink out of UV ink, leading to ink cut-off during printing. Especially when the temperature in winter is low, the fluency of UV ink is far less than that in summer. At this time, not only the equipment nozzles and UV ink need to be heated, but the external working environment also needs a suitable temperature. The suitable ambient temperature for UV flatbed printers is between 15° C and 25° C, and the humidity is between 40% and 70%. There are 6 kinds of reasons that the nozzle does not heat up, and it is easy to solve.

1. keep the machine clean:keep the important parts of the machine clean, can not be stained with oil and dust, keep the hot transfer film clean, can not be stained with fingerprints and dust, keep the bearing products clean, no dust, oil, keep the hands clean, no oil, no sweat.
2.hot stamping pressure:hot stamping pressure must be adjusted to the most appropriate, otherwise too big and easy to hurt the glue head and be hot material, too small and affect the hot stamping effect.The pressure shall be locked after adjusting to the best stamping pressure to avoid change in mass production.
3. hot temperatureIt is easy to damage the bearing material, too low hot temperature may not be able to reach the normal transfer printing.Hot temperature should be determined by the bearing material, flower film, heat transfer machine, these factors, different materials have different hot temperature.
4.hot stamping speed:hot stamping time (speed) should be determined according to the specific hot stamping, in the case of ensuring the hot stamping effect, the faster the speed, the higher the production efficiency, but some products due to some special conditions must use slow speed