Low price 3D cold transfer shrink film direct to film bag for UV printing A3 Size Bag packaging

Easy to operate, compact and convenient, small area does not take up space, and the outside is pleasing to the eye!

Type: DTF Gradient Film Size: 60cm & 30cm*100m/roll Tear off Method: Cold Peel Warranty: 3 Years Note: Store in Dry & Damp-proof Environment

1.Universal matching, easy to use, small size, time-saving and labor-saving
2. Suitable for digital printing and other industries
3. Digital offset heat transfer, one-piece molding
4. No engraving, no waste discharge, no white edge, environmental protection
5. Timing control switch, timing at will
6. Full body sheet metal design, durable and durable
7. Comes with a baking tray limit device, which is more convenient
8. Equipped with power fuse device, more assured to use

The transfer paper can output the pattern to be hot stamped with an inkjet printer, and then print it on the clothes.

Using the shake powder could consider these procedures.
Dusting.
1.What is the powder sprinkled with?Hot melt powder, when the heat is sticky, after the formation of glue coating;
2.Why?Stick hot melt stick to the dry ink to help eventually form the coating;
3.How to sprinkle, sprinkle how fast?Can adjust the knob on the shake powder machine;
4.How much?The powder is about 2-3cm thick to stop sprinkling the powder.
Shaking.
1.Why shake powder?Shake off the excess powder on the ink and film adhesion, so that the powder is thin and evenly attached to the ink.
2.Shake powder speed.Depending on the situation, the knob on the condition machine, about 2-3 gear ok.
Drying.

1.Why drying?Melt the hot melt powder to create a reprint pattern coating;.
2.How long will it bake?Undefinite, depending on the specific situation, mainly to ensure that the pattern feels no powder, hot melt powder all melted into coating.
3.Temperature? 90-130 ° C is ok.

Heat transfer has high requirements for the selection of ink, hot melt powder and transfer film, which is related to the quality of printing and the service life of the machine. The supporting consumables recommended by our factory are the optimal quality and the best supporting scheme.

How to use UV transfer sticker
1. Remove the transfer sticker and tear it off
2. Align the position and paste it
3. Remove the transparent film after pressing the pattern
4. Paste completed

At present, the most widely used laser films on the market mainly include laser aluminized films and laser bronzing films.

DTF PET film with different size for your reference, 30cm*100m/roll and 60cm*100m/roll. This anti-static PET film for cold peel, it can feed continously during printing.Meanwhile, we can also offer other DTF printer consumbles like hot melt powder and pigment ink.

Adopt the main board of the leading enterprise in the domestic textile industry – Hansen main board: use variable point technology to make the printing pattern more delicate and the color more vivid. The components of the textile printing and dyeing printing system include: main control board, spray car board, nozzle driver board, PC processing software, PLC control module, etc.

UV printing is one of the most flexible and exciting print processes ever created, and its uses are almost limitless. For regular object, UV Printing is so convenient. But for irregular object, there are some problems, the AB film solution  is  suitable  for these irregular object and you can also develop a new market of label printing industry. Its just expand the application of UV flatbed printer.

You can print on AGP paper Glitter Gold DTF Film directly with your existing DTF printer and DTF ink, without changing any consumable or DTF printer setting. This Glitter Gold DTF Film works on T-shirts, bags, shoes, socks and other materials, provides you intense sparkle and shine to your prints. The new product has the advantages of glitter Gold effect, high ink absorption, no ink-bleeding, easy peel, and washable.

The advantage of white ink heat transfer is that it can transfer high-precision pictures and other colorful pattern designs. The actual effect is quite close to the computer hand-painted manuscript. The lack of part: if you touch it hard, you will feel a strong sense of collagen fibers, and the ventilation effect is not good. If you only do simple pattern decoration design for clothing products, bags, and pillows, then you don’t need to consider the ventilation problem.

Laser film is a high-tech and environmentally friendly new material developed at the beginning of this century. It can be used to produce composite laser cardboard and transfer laser cardboard through a special production process.

TODOjet DTF printer factory can offer you one-stop solutions like hot melt powder,PET film and pigment ink.We have different pacakge of hot melt powder like 1KG,2KG,5KG and 25KG. Also we have black hot melt powder for your option! For more DTF printer consumables,welcome contact with us!

UV flatbed printers have pass trace, which is theoretically unavoidable, and mechanical errors cannot be eliminated to zero. But the higher the accuracy, the smaller the pass trace phenomenon and will not affect the printing quality. The cause of the pass trace of the pattern: the print feathering is too low, the two-way printing is too fast, the Y-axis belt is loose, the nozzle is in a bad state, and the ink is broken.

Heat transfer medium：T-shirt, sweater, down jacket, canvas bag, jeans, polyester, cotton, cotton, silk, couples wear, parent-child wear, spandex non-woven fabric, cotton cloth, ready-to-wear, chiffon, scarf, vest, underwear, cashmere sweater, book edge, pillowcase, etc.

Symptoms of poor ink output from uv flatbed printers are: flying ink, dripping ink, drawing and so on. There are roughly eight kinds of reasons that cause this kind of failure. In actual application, the UV flatbed printer design varies from different manufacturers. Some may have 10 reasons, and some may have 6 reasons. But mastering the following 7 kinds can solve the problem that 99% of the nozzles have poor ink discharge.

Inkjet technology utilizes tiny droplets of ink to facilitate direct printing without the device coming into contact with the printing surface. Because the technology supports non-contact printing, it can be applied to a variety of media and is now being introduced into a wide range of fields from general-purpose to industrial.

1. Simple control buttons
The key functions are clear and easy to operate, just one touch
2. Four-color printing
The colors are more vivid and rich, and the hot stamping effect is good

Heat transfer machine operation process: adjust the time controller to the required time, put the transferred clothing on the lower ironing board, and then put the heat transfer paper (pay attention to the front and back of the heat transfer paper), press the handle down forcefully, Till the end.

Advantages
1.With timing function, automatic sound &light alarm after completion
2.With lock catch and sealing strip
3.Excellent heat preservation
4.Rapid temperature rise
5.Up to 6 heating tubes
6.Ensure that every corner of the full width can melt
7.It makes the image quality and firmness transferred to the fabric better

UV printers can print the following three effects:
1.Flat color printing
2.Flat 3D color printing
3.3D relief(embossing)

Hotsale A3 DTF printer:
* 2 XP600 printheads support fluoresent ink printing
* Fast speed, can each to 5 sqm/h (6 hours can finish one 100m roll film)
* Support vent holes solution,keep the garment breathable function after transfered
* No limit of fabrics

UV flatbed printer UV lamp belongs to one of the core components of the device. Its main function is to ensure that the UV ink adheres to the pattern surface and can be dried quickly and completely to prevent the pattern from discoloring and falling off. During long-term use, whether it is natural aging of parts or improper manual operation, it will cause fault. There are four common faults: the uv lamp is dimmed, the uv lamp is not off, the uv lamp is not on, and the uv lamp has a wrong lighting distance.

White ink and color ink come out with the environmentally friendly paint heat transfer solution, and the subversive garment heat transfer application process solves the problem of picky fabrics in the direct-injection printing process. The new heat transfer process is not limited to material transfer and no longer needs to worry about color difference and color fastness Problem, Pattern WYSIWYG.

Recently, heat transfer is widely used in garment printing.And in the market,we always see hot peel film and cold peel fim,even now also with warm peel film,but which one is best? Here we can do a analyze from different aspects

China’s UV printer industry has been developing for more than ten years, and it has basically reached a bottleneck in terms of flat-panel printing technology at this stage. Throughout these years, the evolution of nozzles has become a main line. Most UV printer manufacturers have started to change Epson nozzles, Seiko nozzles, Konica nozzles to Ricoh nozzles, Toshiba nozzles, Kyocera nozzles, and starlight nozzles. It is also based on the replacement of nozzles in Japan. The core point of the market is the cost-effectiveness of the print head, that is a better balance between speed, accuracy, life, and price.

Five Guarantees
1. Quality: no fading, strong stickiness
2. Factory: source manufacturers, innovation and worry-free
3. Team: one-to-one service, free design
4. Choice: a variety of crafts for you to choose
5. After-sale: quality problem, free re-send

When something temporarily leaves for a short time and no longer operates, the UV flatbed printer is set to the standby state, and the x-axis and y-axis are also static. If the x-axis carriage movement is found, it means that the fiber cable is damaged or loose.